If your mower blades will not turn after the blade controls have been engaged, your deck belt may be broken. The deck is located directly under the operators seat. This belt spins the mowers blades and runs through a pulley system of idlers. The exact configuration of the deck belt will depend on your model of mower.
for instance, What are spindles on a mower?
The spindle on a riding mower is the post to which the blade attaches and around which it spins when the machine is in action. A riding mower may have one or more spindles, depending on the size of the mower and the way it is manufactured. You may have a problem with one or more spindles at the same time.
significantly, Why won’t my Craftsman mower blades engage?
Common solutions for: Craftsman Lawn mower blades won’t engage. … If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
also How do you engage a lawn mower blade?
Find the plunger at the top of the attachment lift lever. Press the plunger inward with your thumb, and move the attachment lift lever back, or toward you, to lower the cutting blade. Release the plunger and attachment lift lever. Pull the attachment clutch switch outward to “Engage” to make the cutting blade rotate.
Why won’t my Craftsman riding mower blades won’t engage? One of the reasons why the blades on your lawnmower may not engage is the belt. It’s either stretched or too loose, worn-out, or damaged, causing it to fall off easily. It could also snap out of position, especially if you tried to cut more grasses at a time that’s beyond its capacity.
Table of Contents
How long do mower spindles last?
Member. The maintenance free spindles usually last about 2-3 years in commercial use.
How do I know if my axle spindle is bad?
Look for an scarring, gouges, discoloration, or scoring on the spindle. If the spindle is damaged then the bearings won’t ride properly and can fail again or it can cause other problems such as uneven or excessive tire wear and ride quality problems.
How do you engage Craftsman blades?
Find the plunger at the top of the attachment lift lever. Press the plunger inward with your thumb, and move the attachment lift lever back, or toward you, to lower the cutting blade. Release the plunger and attachment lift lever. Pull the attachment clutch switch outward to “Engage” to make the cutting blade rotate.
How do I know if my PTO clutch is bad?
Simple test would be to remove the mower deck belt from the PTO pulley and try to engage the PTO. If it doesn’t stall, the clutch is not your problem. If it does stall I would guess you’ve had a bearing fail in the clutch. The other thing to check is the seat switch if it’s still enabled.
Why does my riding mower dies when I engage the blades?
If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged. … The pulleys in your lawn tractor are driven by the drive belt, and turn the spindles. If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged.
Why wont my blades engage on my John Deere mower?
There could be a problem with safety switches. On most newer model lawn mowers, the brake has to be disengaged or off for the blades to operate. You also have to be sitting on the seat to engage the PTO, so the seat switch may be malfunctioning.
Why won’t my blades won’t engage?
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
What does a bad mower spindle sound like?
Buzzing Noises & Vibration
Similarly to the squealing, if the mower starts to make buzzing noises while mowing your grass, it probably means it has a bad spindle. Likewise, you’ll feel how the mower begins to vibrate out of nowhere.
How often do you grease mower spindles?
The spindles and caster wheels are generally the most often greased. The spindles and castor wheels should be done around once a month because of the moving interior parts. Commercial mowers that put hundreds of hours on their Ferris mower would be looking at greasing the mower everyday depending on usage.
Can you over grease mower spindles?
“GREASING MOWER SPINDLES” “Grease fittings on mower spindles are used for assembly only. DO NOT grease spindles or damage may occur to bearing seals”.
How do you know if your trailer axle is bad?
In the case of a multi-axle trailer, you are looking for all of the bulges of the tires to make contact with the straightedge, or to be very close, say within 1/8″. If there are larger gaps between the bulges & the straightedge, it indicates a bent axle, a bent spindle, or a bent wheel.
When should axle spindles be replaced?
Worst case is the hub and wheels leave the vehicle and the spindle hits the ground causing it to bend. In these cases the whole spindle needs to be replaced. If you have more than 1 damaged surface, it means the spindle took some abuse and it would be better to replace the spindle.
Is the spindle part of the axle?
Spindles are the innermost part of the trailer wheel and axle assembly. They provide a surface for the wheel bearings and wheel hub to rotate around.
Why does my lawn mower stall when I engage the blades?
The pulleys in your lawn tractor are driven by the drive belt, and turn the spindles. If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged. … If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged.
Why does my riding mower keep stalling?
A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall.
Why is my John Deere mower dying?
Dirt simply clogs fuel flow, resulting in an engine that sputters and stalls. … Replace the fuel filter, too, which could have absorbed too much dirt or water to be effective. Check the gas tank cap. It should have a small vent hole on top that allows back pressure for proper fuel flow.
Why does my lawn mower shut off while mowing?
Being Overworked. One of the most common reasons that a lawn mower might stall while it is cutting grass is that it is being overworked. This is a mechanism that is intentionally incorporated into the mower to prevent the motor from being blown.
Why wont my blades won’t engage?
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
Why does the belt keep coming off my John Deere mower?
The drive belt may come off a riding mower because it is damaged or loose. … If broken or worn, the belt can break while the engine runs, and it can fly off at a great velocity, which is highly dangerous. Check the belt for looseness, cracks, fraying or separation from the rest of the assembly, and replace if necessary.
Discussion about this post