BTE manufactures all of the critical components to make the powerglide transmission the best choice for drag racing. We offer a variety of gear ratios, input shafts, clutch drums, roller components, and other items to custom fit almost any high performance vehicle.
in fact, What is the best gear ratio for 1/4 mile?
A 4.10 gear would be your best bet to get because it will push the weight out of the hole and it would be easier to adjust your MPH with tire size.
for instance, How much horsepower will a 2 speed Powerglide handle?
With all the available upgrades, both the Powerglide and the TH400 are capable of withstanding an incredible 3,500 horsepower.
indeed Why is the Powerglide so good? The Powerglide has just two speeds: low and high. And its durability allows it to run 100 to 150 races before needing a rebuilding that takes only two hours, Coughlin says. “It’s bulletproof, simple and easy to customize,” he says.
What is the strongest GM transmission?
The 6L90 is the strongest of GM’s family of Hydra-Matic six-speed automatic transmissions.
Table of Contents
Are 3.73 gears good for highway?
Rear end gears (2.79’s, 3.00’s, 3.25’s, etc) are great for freeway driving, bit not good for 0-60 MPH or accelerating from a dead stop. Shorter gears (higher numbers) are much better suited for accelerating, such as 3.55, 3.73, 3.91’s, 4.11’s etc. Always remember, for very “give” there is a “take”.
What gear ratio is best for acceleration?
A lower (taller) gear ratio provides a higher top speed, and a higher (shorter) gear ratio provides faster acceleration. . Besides the gears in the transmission, there is also a gear in the rear differential. This is known as the final drive, differential gear, Crown Wheel Pinion (CWP) or ring and pinion.
Does gear ratio affect horsepower?
A higher numeric axle ratio (4.11:1) keeps the engine running in the higher horsepower range, thus improving performance.
Will a Powerglide bolt up to a 350?
The powerglide should be fine with the 350 unless it is an air cooled version.
Is a Powerglide Streetable?
They are very streetable. I have several guys with glides and a gear vendor OD unit giving them a 4 speed trans if they split shift them.
How much horsepower can a 350 transmission handle?
The Stage 1 TH350 is rated up to 450 hp.
Why do people use Powerglide?
In fact, a Powerglide can weigh less than a standard manual transmission, provide a direct-drive feel with minimal slippage at the torque converter (or none at all with direct drive), and maintain a relatively low rotating mass. Many Street Stocks, I.M.C.A.
How do I know if my transmission is 2 speed Powerglide?
Identifying a Powerglide Transmission
Identify early cast-iron Powerglides by locating the word “Powerglide,” stamped on the passenger side of the transmission. Another identification feature is that the cast-iron models have no pan on the bottom of the transmission.
Which transmission is better 6L80 or 6L90?
What is the difference between 6L80 and 6L90 transmission? The main difference between the 6L80 transmission and 6L90 transmission is the strength of the internal components. The 6L90 transmission case is 1-3/8” longer, which provides extra room to house two additional pinion gears (6 total).
Are Turbo 350 transmissions good?
The TH350 is an automatic shift, three-speed transmission. It is widely considered to be one of the greatest of automatic transmissions ever built. … The Turbo 350 is the shortest and one of the strongest automatics that can be put into a Jeep.
What transmission can handle 1500 HP?
ATI Performance Racing® Transmissions are well known in the drag racing world for both their reliability and horsepower holding capability. ATI has taken their 57 years of experience and applied it to the 4L85E GM 4 speed, overdrive transmission.
Are 3.73 or 4.10 gears better?
3.73 VS 4.10 Ratio
| 3.73 Ratio | 4.10 Ratio |
|---|---|
| Not as fast off of the line | Quicker Off The Line |
| Lower Torque | Higher Torque |
| Better Gas Mileage | Decreased Gas Mileage |
| Higher Top Speed | Lower Top Speed |
Is 3.42 or 3.73 better?
The 3.42 is fine for towing smaller boats, plus you will get better gas mileage for everyday driving. If I were towing frequently on hilly roads, I might would go for the 3.73 for better gas mileage while towing, but the 3.42 should be fine with a 205.
Are 4.10 gears good for highway?
Installing 4.10 gears improves the car’s performance on the track but with negligible effects to the highway driving. … Switching from a gear set of 3.55 or 3.73 to 4.10 gears will affect your gas mileage slightly as your engine will be turning more times to rotate the rear wheels once.
Are 3.73 or 4.10 gears better?
4.10s are going to accelerate faster and decelerate faster on lift. However the trade off is greater fuel consumption per mile driven and higher engine speed per given road speed. In basic terms the 4.10s will feel quicker and 3.73 will feel faster.
Is 3.25 a good gear ratio?
3.25s are a good all around gear.
What gear ratio is best for torque?
A numerically higher axle ratio provides a mechanical advantage to send more of the engine’s available torque to the rear tires (and front tires, in a four-wheel drive vehicle), but you pay the price at the fuel pump. So, a truck with optional 3.73 gears will tow a heavier trailer than one with 3.55 or 3.21.
What gear ratio is better for torque?
In general, a lower final drive ratio will lead to less torque at the wheels but a higher top speed. Meanwhile, a higher ratio will result in the opposite, i.e. more torque at the wheels but a lower top speed.
Is it better to have more torque or horsepower?
Torque, simply, is the ability of a vehicle to perform work — specifically, the twisting force applied by the crankshaft. Horsepower is how rapidly the vehicle can perform that work. … Because there is generally a limit on how fast you can spin an engine, having higher torque allows for greater horsepower at lower rpms.
Discussion about this post