It does not make any difference what port you use to connect to the internet. Your smart devices will connect to the internet through the switch. … It does not make any difference what port you use to connect to the internet. Your smart devices will connect to the internet through the switch.
particularly, Which cable is used to connect switch to switch?
Unsourced material may be challenged and removed. An Ethernet crossover cable is a crossover cable for Ethernet used to connect computing devices together directly. It is most often used to connect two devices of the same type, e.g. two computers (via their network interface controllers) or two switches to each other.
thus, Why is switch better than hub?
Switch: A switch is smarter than a hub. Similar to the hub, it is a connection point for all the devices in the network. However, it is more efficient at passing a data packet across the network. It records the MAC addresses of the computers connected to it in a tabular format.
in effect What comes first router or switch?
1 Answer. Assuming a normal residential setup, you need to put the switch after the router. because the modem will only talk to the first computer that talks to it. To share the connection, you need a router.
Does daisy-chaining switches slow down network?
There are no hard limit on daisy-chaining switches. I had a layer 2 network once where a PC at one end of the network, reaching a server at the other end could easily go via about a dozen switches.
Table of Contents
Is crossover cable Still Needed?
Crossover cables are still needed in one specific scenario – to connect devices that aren’t outfitted with Gigabit Ethernet functionality. This is a high-quality, high-speed standard found in most but not all modern devices that support Ethernet.
How do you stack a switch?
Generally, there are two ways to stack switches together: through stackwise port or via stacking/uplink port. The typical method for switch stacking is to use stacking cable via stackwise port. Take Cisco 3750 series stack switches for example. Stackwise port lies on the rear-panel.
Do you need a crossover cable between switches?
No, you do not need a crossover cable to connect two switches, with qualifications. Most (probably all) modern switches have either an auto detect port(s) or a manual uplink switch for a particular port.
Should I use a hub or switch?
Switch is more efficient than the hub. A switch can join multiple computers within one LAN, and a hub just connects multiple Ethernet devices together as a single segment. Switch is smarter than hub to determine the target of the forwarding data.
Should I buy hub or switch?
By generating less network traffic in delivering messages, the Ethernet switch performs better than a hub in busy networks. For a small network with lesser users or devices, a hub can easily deal with network traffics. It will be a cheaper option for a network cabling.
What is more secure hub or switch?
Why are switches more secure than hubs? Switches don’t require port mirroring for a network analyst to monitor traffic. … Switches will transmit data only to specific network devices, rather than broadcasting the same data to all of the devices in a network.
Should I use a switch or a router?
While a network switch can connect multiple devices and networks to expand the LAN, a router will allow you to share a single IP address among multiple network devices. In simpler terms, the Ethernet switch creates networks and the router allows for connections between networks.
Can I put a switch before a router?
Probably not unless your modem integrates the function of a router so that you can rewire and reconfigure the wireless router to set it up as access point. Seen from the outside, you indeed put a managed switch before router, however it still follows the principle that router goes before network switch.
Can a router be behind a switch?
Yes you need to have your router first. Your ISP only gives you 1 IP address aka 1 device can be connected at the same time.
Can I connect a switch to a router?
Connect an Ethernet cable to one of the ports at the back of the switch, then connect the other end to one of the Ethernet ports at the back of the router. NOTE: In this example, we are using the E4200 router and the SE1500 switch.
Do switches slow down network?
Ethernet switch won’t slow down your connection speed.
How many switches can be cascaded?
(
Up to 384 ports
, IIRC). Those cards each have 48 ports, and they are technically ‘cascaded’ switches, in that they are connected via the backplane of the switch chassis.
…
How many switches can I cascade?
| Xyzzy Ars Tribunus Angusticlavius et Subscriptor Registered: Jul 9, 2000 Posts: 9635 | Posted: Wed Apr 03, 2002 12:57 pm |
|---|---|
| 7? |
Apr 3, 2002
Why does a crossover cable have different ends?
Unlike straight through cable, the RJ45 crossover cable uses two different wiring standards: one end uses the T568A wiring standard, and the other end uses the T568B wiring standard. The internal wiring of Ethernet crossover cables reverses the transmit and receive signals.
What are the correct pinouts for a crossover cable?
According to 32 reports in our database (23 positive and 7 negative) the Ethernet 10/100/1000 Mbit crossover cable pinout should be correct.
Why crossover cable is needed for two computers?
Crossover cable enables one to establish a direct connection between two computing devices using Ethernet ports. It Connects two computers directly. You can connect two hubs/switches by using the normal port in both switches and hubs.
How many switches can be stacked?
A switch stack is a set of up to 8 switches connected through their stacking ports.
What are the benefits of switch stacking?
Benefits of the Switch Stacking
- It reduces the management overhead.
- By reducing the required number of switches, it also reduces the cost of the network.
- It allows us to add or remove switches at any time without disrupting the running network or affecting its performance.
How many 2960 switches can be stacked?
Up to eight switches can be stacked in a ring topology using the FlexStack plus or FlexStack extended modules. If there is an existing stack of Cisco Catalyst 2960-X or 2960-XR Series Switches, the hybrid FlexStack extended module allows you to add new switches across the wiring closet to the same stack.
What is the color code for crossover cable?
A crossover has one end with the Orange set of wires switched with the Green set. Odd numbered pins are always striped, even numbered pins are always solid colored. Looking at the RJ-45 with the clip facing away from you, Brown is always on the right, and pin 1 is on the left.
Why are crossover cables rarely used nowadays?
Why are crossover cables rarely used nowadays? … Because 10BaseT and 10BaseFL use different types of cables you can use a(n) (blank) interconnect different Ethernet types.
Discussion about this post